VNB10N07-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Number of Pins | 3 |
| Packaging | Tube |
| Series | OMNIFET™, VIPower™ |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 100mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 50W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Base Part Number | VNB10 |
| Pin Count | 3/2 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 10A |
| Operating Supply Voltage | 18V |
| Interface | On/Off |
| Nominal Supply Current | 250μA |
| Output Configuration | Low Side |
| Power Dissipation | 50W |
| Output Current | 7A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 250μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 100 μs |
| Switch Type | General Purpose |
| Nominal Input Voltage | 18V |
| Turn-Off Delay Time | 400 μs |
| Continuous Drain Current (ID) | 10A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 55V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 10V |
| Turn On Time | 0.9 µs |
| Output Peak Current Limit-Nom | 10A |
| Rds On (Typ) | 100m Ω (Max) |
| Drain to Source Resistance | 140mOhm |
| Turn Off Time | 6 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 4.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VNB10N07-E Overview
The package is in the form of a Tube.This package is included in TO-263-3, D2Pak (2 Leads + Tab), TO-263AB.This LED driving board is mounted using the mounting type Surface Mount.The switch type is General Purpose.The lighting driver has a total of 1 outputs that are available for use.The LED driving board operates at Not Required volts.A maximum voltage of N-Channel volts is available from the output of this LED driver.As you can see, it comes from the VNB10 family.In total, there are 2 terminations.It is necessary to use the 3 pins in order to operate the LED driver.Currently, there are 1 functions associated with the lighting driver.To comply with the operation criteria, the maximum output current is reduced to 10A.Surface Mount is mounted in the way.A total of 3/2 pins are included in this LED driver.100mOhm resistance is present in the lighting driver.This electrical component is part of the OMNIFET?, VIPower? series.This results in a 7A output current.In order to optimize the efficiency of the supply voltage, it should be set to 18V.For its operation, a current of 250μA is required.
VNB10N07-E Features
Resistance of 100mOhm
VNB10N07-E Applications
There are a lot of STMicroelectronics VNB10N07-E Power Switches ICs applications.
- Hot-Swap Systems
- USB Power Distribution
- Set-Top Boxes
- Notebook and Tablet Computers
- Mobile Communication Devices
- Wireless Modem Data Cards
- Wireless Headsets
- Low Voltage I/O System Power
- Set-top-box
- Portable Devices
