VNB14NV04-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Number of Pins | 3 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | OMNIFET II™, VIPower™ |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 35mOhm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Power Dissipation | 74W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VNB14 |
| Pin Count | 3 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 18A |
| Operating Supply Voltage | 18V |
| Interface | On/Off |
| Nominal Supply Current | 100μA |
| Output Configuration | Low Side |
| Power Dissipation | 74W |
| Output Current | 12A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 100μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 80 ns |
| Switch Type | General Purpose |
| Rise Time | 350ns |
| Fall Time (Typ) | 150 ns |
| Turn-Off Delay Time | 450 ns |
| Continuous Drain Current (ID) | 14A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 42V |
| Turn On Time | 4.5 µs |
| Output Peak Current Limit-Nom | 18A |
| Rds On (Typ) | 35m Ω (Max) |
| Turn Off Time | 25 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height | 4.6mm |
| Length | 10.4mm |
| Width | 9.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VNB14NV04-E Overview
It is packaged in the form of a Tube.The TO-263-3, D2Pak (2 Leads + Tab), TO-263AB package includes it.A Surface Mount mounting is used for the LED driving board.It owns the General Purpose switch type.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.In this LED driver, there are no outputs available.To operate, it needs a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be obtained with this LED driver.It is a member of the VNB14 family.It has a total of 2 terminations.3 pins are used for operation.It is important to note that the LED driving board has 1 functions.To meet the operation criteria, the maximum output current drops to 18A.It is mounted in the way of Surface Mount.This LED driver is equipped with a total of 3 pins.In this case, there is 35mOhm resistance in the LED driving board.These electrical components are part of the OMNIFET II?, VIPower? series.In this case, the output current will be set to 12A.When using this LED driving board, it is recommended that the supply voltage is set to 18V.It requires a maximum current requirement of 100μA.
VNB14NV04-E Features
Resistance of 35mOhm
VNB14NV04-E Applications
There are a lot of STMicroelectronics VNB14NV04-E Power Switches ICs applications.
- Telecom and Network Systems
- Portable/Handheld Devices
- Solid State Drivers
- Storage Drives
- Hot Swaps
- Wireless Modem Data Cards
- USB Protection
- Hot Swap
- Hot Swap
- Solid-State Drives
