VNB35N07-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Number of Pins | 3 |
| Packaging | Tube |
| Series | OMNIFET™, VIPower™ |
| Feature | Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 28mOhm |
| Max Power Dissipation | 125W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Base Part Number | VNB35 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 35A |
| Operating Supply Voltage | 18V |
| Interface | On/Off |
| Nominal Supply Current | 250μA |
| Output Configuration | Low Side |
| Power Dissipation | 125W |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 500μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 200 ns |
| Switch Type | General Purpose |
| Max Input Voltage | 18V |
| Drain to Source Voltage (Vdss) | 70V |
| Nominal Input Voltage | 18V |
| Turn-Off Delay Time | 1 μs |
| Continuous Drain Current (ID) | 35A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 55V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 70V |
| Turn On Time | 800 μs |
| Output Peak Current Limit-Nom | 35A |
| Rds On (Typ) | 28m Ω (Max) |
| Drain to Source Resistance | 28MOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height | 4.6mm |
| Length | 10.28mm |
| Width | 9.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VNB35N07-E Overview
The package is in the form of a Tube.It is included with the TO-263-3, D2Pak (2 Leads + Tab), TO-263AB package as well.A Surface Mount mounting is used for the LED driving board.There is a General Purpose switch type associated with it.The LED driver has 1 outputs.In order to operate, it requires a voltage supply of Not Required.Voltage output is N-Channel volts at maximum.It has a total of Status Flag features.It belongs to the VNB35 family.It has a total of 2 terminations.During operation, the 3 pins are used.There are 1 functions of the LED driver.The maximum output current is reduced to 35A to meet the operation criteria.In this case, it is mounted in the way of Surface Mount.It has a resistance of 28mOhm.The OMNIFET?, VIPower? series includes this electrical component.It is set to 25A in this case.The supply voltage should be set at 18V for best efficiency.It has a maximum input voltage of 18V volts.There is a maximum current requirement of 500μA for its operation.
VNB35N07-E Features
Resistance of 28mOhm
VNB35N07-E Applications
There are a lot of STMicroelectronics VNB35N07-E Power Switches ICs applications.
- Wireless Modem Data Cards
- Portable/Handheld Devices
- Telecom and Network Systems
- PC Card Hot Swap
- Wireless Headsets
- Wireless/Networking Cards
- Notebook and Tablet Computers
- HDD and SSD
- USB Power Distribution
- HDD, SSD
