VNB35NV0413TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Number of Pins | 3 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | OMNIFET II™, VIPower™ |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 13mOhm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Power Dissipation | 125W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Base Part Number | VNB35 |
| Pin Count | 3 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 45A |
| Operating Supply Voltage | 18V |
| Interface | On/Off |
| Nominal Supply Current | 100μA |
| Output Configuration | Low Side |
| Power Dissipation | 125W |
| Output Current | 30A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 100μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 12 μs |
| Switch Type | General Purpose |
| Output Current per Channel | 30A |
| Drain to Source Voltage (Vdss) | 70V |
| Turn-Off Delay Time | 120 μs |
| Continuous Drain Current (ID) | 35A |
| Ratio - Input:Output | 1:1 |
| Gate to Source Voltage (Vgs) | 20V |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 70V |
| Output Peak Current Limit-Nom | 45A |
| Rds On (Typ) | 13m Ω (Max) |
| Drain to Source Resistance | 10mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 4.826mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VNB35NV0413TR Overview
It is package in Tape & Reel (TR) case.It is included in the package TO-263-3, D2Pak (2 Leads + Tab), TO-263AB.Mounting type Surface Mount is selected for the LED driving board.General Purpose is the switch type it owns.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.The LED driver is equipped with 1 outputs.In order to operate, it requires a voltage supply of Not Required.Voltage output is N-Channel volts at maximum.It is a member of the VNB35 family.It contains 2 terminations.For operation, 3 pins are used.As far as the lighting driver is concerned, there are 1 functions.This results in the maximum output current dropping to 45A to meet the operation criteria.The lighting driver is mounted in the way of Surface Mount.There are 3 pins in total on this board.Currently, the LED driving board has 13mOhm resistance.Electrical components such as this are included in the OMNIFET II?, VIPower? series.This case has the output current set to 30A.For maximum efficiency, the supply voltage should be set to 18V.There is a maximum current requirement of 100μA for its operation.
VNB35NV0413TR Features
Resistance of 13mOhm
VNB35NV0413TR Applications
There are a lot of STMicroelectronics VNB35NV0413TR Power Switches ICs applications.
- Wireless Modem Data Cards
- Storage Drives
- Handheld Devices
- Hard Disk Drives
- HDD, SSD
- Wireless Headsets
- Portable GPS
- Low Voltage I/O System Power
- Smartphone and PDA
- USB Ports/Hubs
