Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 7 months ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
TO-252-3, DPak (2 Leads + Tab), SC-63 |
Number of Pins |
3 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tube |
Series |
OMNIFET II™, VIPower™ |
JESD-609 Code |
e3 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
2 |
ECCN Code |
EAR99 |
Resistance |
35mOhm |
Terminal Finish |
Tin (Sn) |
Max Power Dissipation |
74W |
Terminal Position |
SINGLE |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Terminal Pitch |
2.25mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
VND14 |
Pin Count |
3 |
JESD-30 Code |
R-PSSO-G2 |
Output Type |
N-Channel |
Max Output Current |
12A |
Interface |
On/Off |
Nominal Supply Current |
100μA |
Output Configuration |
Low Side |
Power Dissipation |
74W |
Output Current |
18A |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Max Supply Current |
100μA |
Input Type |
Non-Inverting |
Turn On Delay Time |
1.5 μs |
Switch Type |
General Purpose |
Rise Time |
9.7μs |
Drain to Source Voltage (Vdss) |
55V |
Fall Time (Typ) |
10.2 μs |
Turn-Off Delay Time |
25 μs |
Continuous Drain Current (ID) |
7A |
Threshold Voltage |
2.5V |
Ratio - Input:Output |
1:1 |
Voltage - Load |
36V Max |
Fault Protection |
Current Limiting (Fixed), Over Temperature, Over Voltage |
Drain to Source Breakdown Voltage |
40V |
Number of Drivers |
1 |
Turn On Time |
4.5 μs |
Output Peak Current Limit-Nom |
18A |
Rds On (Typ) |
35m Ω (Max) |
Drain to Source Resistance |
35mOhm |
Built-in Protections |
TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
Height |
2.63mm |
Length |
6.6mm |
Width |
6.2mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
VND14NV04-E Overview
It's?packaged?in?the way?of?a?Tube.It's included in the TO-252-3, DPak (2 Leads + Tab), SC-63 package.The mounting type of the LED driver is Surface Mount.There is a switch type of General Purpose.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.With a supply voltage of Not Required, the LED driving board operates.A maximum voltage of N-Channel volts is available from the output of this LED driver.As you can see, it comes from the VND14 family.A total of 2 terminations have been found in it.During operation, the 3 pins are used.It is important to note that the LED driving board has 1 functions.Maximum output current falls to 12A when operation criteria are met.The LED driving board is mounted in the way of Surface Mount.The LED driving board is equipped with a total of 3 pins.It has a resistance of 35mOhm.It is part of the OMNIFET II?, VIPower? series.It is set to 18A in this case.A maximum current requirement of 100μA is required for its operation.The part has 1 drivers.
VND14NV04-E Features
Resistance of 35mOhm
VND14NV04-E Applications
There are a lot of STMicroelectronics VND14NV04-E Power Switches ICs applications.
- Handheld Devices
- USB Power Distribution
- Storage (HDDs, SSDs)
- Wireless Headsets
- Set-top-box
- Portable GPS
- Smart Phones, Feature Phones
- Portable/Handheld Devices
- Hot-Swap Systems
- Hard Disk Drives