VND5004ASP30TR-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 30-PowerSOP (0.630, 16.00mm Width) |
| Number of Pins | 30 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | VIPower™ |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 30 |
| ECCN Code | EAR99 |
| Resistance | 4mOhm |
| Terminal Finish | MATTE TIN |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 1mm |
| Base Part Number | VND5004 |
| Pin Count | 30 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 100A |
| Operating Supply Voltage | 13V |
| Interface | On/Off |
| Nominal Supply Current | 6mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 6mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 25 μs |
| Switch Type | General Purpose |
| Output Current per Channel | 70A |
| Turn-Off Delay Time | 35 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.5V~27V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 100A |
| Rds On (Typ) | 4m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Output Current Flow Direction | SINK |
| Width | 16mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VND5004ASP30TR-E Overview
Tape & Reel (TR) is the way it's packaged.It is included with the 30-PowerSOP (0.630, 16.00mm Width) package as well.This lighting drivere has a mounting type of Surface Mount.There is a General Purpose switch type associated with it.To ensure reliable operation, set the temperature to -40°C~150°C TJ.It is possible to use 2 outputs in the lighting driver.The LED driving board operates at Not Required volts.A maximum voltage of N-Channel volts is available from the output of this LED driver.This LED driving board is equipped with Auto Restart features in order for it to be useful.It is a member of the VND5004 family.A total of 30 terminations have been recorded.During operation, the 30 pins are used.It is important to note that the LED driving board has 1 functions.The maximum output current is reduced to 100A to meet the operation criteria.High efficiency is possible when the supply voltage is set to 13V.In this case, it is mounted in the way of Surface Mount.A total of 30 pins are included in this LED driver.It has a resistance of 4mOhm.This electrical component can be found in the VIPower? series.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.When using this LED driving board, it is recommended that the supply voltage is set to 13V.It has a maximum current requirement of 6mA.
VND5004ASP30TR-E Features
Supplied from 13V
Resistance of 4mOhm
VND5004ASP30TR-E Applications
There are a lot of STMicroelectronics VND5004ASP30TR-E Power Switches ICs applications.
- Hot Swaps
- Mobile Communication Devices
- USB3.1 Power Delivery
- USB Power Distribution
- HDD, SSD
- Solid State Drivers
- Portable GPS Device
- Hot Swap
- Portable Music Players
- Smartphone and PDA
