VND5025LAK-E
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-PowerBSOP (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | VIPower™ |
| Feature | Auto Restart |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Subcategory | Peripheral Drivers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.8mm |
| Base Part Number | VND5025 |
| Pin Count | 24 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 40mA |
| Operating Supply Voltage | 13V |
| Supply Voltage-Max (Vsup) | 36V |
| Power Supplies | 8/36V |
| Interface | On/Off |
| Nominal Supply Current | 6mA |
| Output Configuration | High Side |
| Output Current | 40A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 6mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 35 μs |
| Switch Type | General Purpose |
| Turn-Off Delay Time | 50 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.5V~36V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Rds On (Typ) | 25m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VND5025LAK-E Overview
It is packaged in the manner of a Tube.It is included with the 24-PowerBSOP (0.295, 7.50mm Width) package as well.A Surface Mount mounting is used for the LED driving board.There is a General Purpose switch type associated with it.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.The LED driver has a total of 2 outputs.It uses a supply voltage of Not Required to operate.A maximum output voltage of N-Channel volts can be obtained with this LED driver.This LED driving board is equipped with Auto Restart features in order for it to be useful.It belongs to the VND5025 family.The termination count is 24.The 24 pins are used to operate the LED driver.Currently, the lighting driver has a total of 1 functions.This results in the maximum output current dropping to 40mA to meet the operation criteria.A supply voltage of 13V leads to high efficiency.In this case, it is mounted in the way of Surface Mount.24 pins are equipped with it.This electrical component can be found in the VIPower? series.When this case is used, the output current is set to 40A.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.The maximum supply voltage for this lighting driver is set to 36V (Vsup).This part has a power supply of 8/36V.It is recommended to set the supply voltage to 13V for optimum efficiency.There is a maximum current requirement of 6mA for its operation.
VND5025LAK-E Features
Supplied from 13V
VND5025LAK-E Applications
There are a lot of STMicroelectronics VND5025LAK-E Power Switches ICs applications.
- PC Cards
- Hard Disk Drives
- Portable/Handheld Devices
- Wireless Headsets
- Set-Top Boxes
- Hot Swap
- Set-top-box
- Portable GPS Device
- Low Voltage I/O System Power
- Wireless Modem Data Cards
