VND5050AKTR-E
| Parameters | |
|---|---|
| Base Part Number | VND5050 |
| Pin Count | 24 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 18A |
| Supply Voltage-Max (Vsup) | 36V |
| Power Supplies | 8/36V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Interface | On/Off |
| Nominal Supply Current | 3mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 5μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 25 μs |
| Switch Type | General Purpose |
| Output Current per Channel | 12A |
| Turn-Off Delay Time | 35 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.5V~36V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Rds On (Typ) | 50m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SOURCE |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOP (0.295, 7.50mm Width) Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | VIPower™ |
| Feature | Auto Restart |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 50mOhm |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.8mm |
VND5050AKTR-E Overview
As you can see, it's packaged in the way of a Tape & Reel (TR).Package 24-SOP (0.295, 7.50mm Width) Exposed Pad contains it.The lighting driver has the mounting type Surface Mount.General Purpose is the switch type that it owns.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.The lighting driver has a total of 2 outputs that are available for use.It uses a supply voltage of Not Required to operate.A maximum output voltage of N-Channel volts has been specified.In terms of features, the LED driving board has Auto Restart.The VND5050 family consists of this type.A total of 24 terminations can be found in it.The operation is carried out using the 24 pins.There are 1 functions of the LED driver.In order to meet the operation criteria, the maximum output current drops to 18A.Supply voltages of 13V allow for high efficiency.In this case, it is mounted in the way of Surface Mount.In total, it has 24 pins.In this LED driving board, there is 50mOhm resistance.There is an electrical component included in the VIPower? series.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.The maximum supply voltage is set to 36V.For normal operation, the supply voltage (Vsup) must be kept above 4.5V.The power supply of the part is 8/36V.There is a maximum current requirement of 5μA for its operation.
VND5050AKTR-E Features
Supplied from 13V
Resistance of 50mOhm
VND5050AKTR-E Applications
There are a lot of STMicroelectronics VND5050AKTR-E Power Switches ICs applications.
- Low Voltage I/O System Power
- USB3.1 Power Delivery
- Mobile Communication Devices
- Telecom and Network Systems
- Hot Swaps
- USB Power Distribution
- Gaming
- Hot Swap
- Notebook PC
- Smart Phones, Feature Phones
