Parameters |
Length |
10.3mm |
Width |
7.5mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 8 months ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
PowerSO-36 Exposed Bottom Pad |
Number of Pins |
36 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tube |
Series |
VIPower™ |
JESD-609 Code |
e3 |
Feature |
Auto Restart |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
36 |
ECCN Code |
EAR99 |
Resistance |
11mOhm |
Terminal Finish |
Matte Tin (Sn) - annealed |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Terminal Pitch |
0.5mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
VND5E012 |
Pin Count |
36 |
Number of Outputs |
2 |
Qualification Status |
Not Qualified |
Output Type |
N-Channel |
Max Output Current |
74A |
Operating Supply Voltage |
13V |
Supply Voltage-Min (Vsup) |
4.5V |
Interface |
On/Off |
Analog IC - Other Type |
ANALOG CIRCUIT |
Nominal Supply Current |
3.5mA |
Output Configuration |
High Side |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Max Supply Current |
6.5mA |
Input Type |
Non-Inverting |
Turn On Delay Time |
30 μs |
Switch Type |
General Purpose |
Output Current per Channel |
52A |
Turn-Off Delay Time |
20 μs |
Ratio - Input:Output |
1:1 |
Voltage - Load |
4.5V~28V |
Fault Protection |
Current Limiting (Fixed), Over Temperature, Over Voltage |
Rds On (Typ) |
11m Ω |
VND5E012AY-E Overview
Tube is the way it's packaged.It's included in the PowerSO-36 Exposed Bottom Pad package.The mounting type of the LED driver is Surface Mount.This switch is of type General Purpose.It is best to set the temperature to -40°C~150°C TJ to ensure reliable operation.The LED driver has a total of 2 outputs.A voltage of Not Required is used to power it.A maximum voltage of N-Channel volts is available from the output of this LED driver.A lighting driver with Auto Restart features is available.It belongs to the family VND5E012.A total of 36 terminations have been recorded.The 36 pins are used for the operation of the system.The LED driver has 1 functions.The maximum output current must drop to 74A to meet the operation criteria.The LED driving board is mounted in the way of Surface Mount.The LED driving board is equipped with a total of 36 pins.Currently, the LED driving board has 11mOhm resistance.This electrical component is part of the VIPower? series.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 4.5V.There is an analog input IC in this gadget, which is ANALOG CIRCUIT.It is recommended to set the supply voltage to 13V for optimum efficiency.It has a maximum current requirement of 6.5mA.
VND5E012AY-E Features
Resistance of 11mOhm
VND5E012AY-E Applications
There are a lot of STMicroelectronics VND5E012AY-E Power Switches ICs applications.
- Mobile Communication Devices
- Telecom and Network Systems
- Smartphone and PDA
- Portable GPS Device
- Portable Devices
- Portable Music Players
- Hot-Swap Systems
- Hard Disk Drives
- Storage Drives
- USB Protection