VND5E050MJ-E
| Parameters | |
|---|---|
| Nominal Supply Current | 3mA |
| Output Configuration | High Side |
| Output Current | 27A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 6mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 20 μs |
| Switch Type | General Purpose |
| Turn-Off Delay Time | 45 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.5V~28V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Rds On (Typ) | 50m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSSO-12 |
| Number of Pins | 12 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | VIPower™ |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.8mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VND5E050 |
| Pin Count | 12 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 19A |
| Supply Voltage-Min (Vsup) | 4.5V |
| Interface | On/Off |
VND5E050MJ-E Overview
Tube is the way it's packaged.In the PowerSSO-12 package, it is included.Mounting type Surface Mount is selected for the LED driving board.General Purpose is the type of switch owned by it.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.The LED driver has a total of 2 outputs.Operation is based on a supply voltage of Not Required.Voltage output is N-Channel volts at maximum.There are Auto Restart features available on the LED driving board.The VND5E050 family contains this object.A total of 12 terminations have been found in it.12 pins are used for operation.As far as the lighting driver is concerned, there are 1 functions.The maximum output current is reduced to 19A to meet the operation criteria.High efficiency is possible when the supply voltage is set to 13V.It is mounted in the way of Surface Mount.A total of 12 pins are present on it.It is included in the VIPower? series.This case has the output current set to 27A.A container with a capacity of Peripheral Drivers contains this self-contained lighting driver.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 4.5V.There is a maximum current requirement of 6mA for its operation.
VND5E050MJ-E Features
Supplied from 13V
VND5E050MJ-E Applications
There are a lot of STMicroelectronics VND5E050MJ-E Power Switches ICs applications.
- Solid-State Drives
- PC Card Hot Swap
- Hot Swap
- Smart Phones, Feature Phones
- Hard Disk Drives
- Portable/Handheld Devices
- PDAs
- PC Cards
- Storage Drives
- Portable Music Players
