VND5E050MKTR-E
| Parameters | |
|---|---|
| Input Type | Non-Inverting |
| Turn On Delay Time | 20 μs |
| Switch Type | General Purpose |
| Output Current per Channel | 19A |
| Turn-Off Delay Time | 45 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.5V~28V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Rds On (Typ) | 50m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Length | 10.3mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-PowerBSOP (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | VIPower™ |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 50mOhm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.8mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VND5E050 |
| Pin Count | 24 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 27A |
| Supply Voltage-Min (Vsup) | 4.5V |
| Interface | On/Off |
| Nominal Supply Current | 3mA |
| Output Configuration | High Side |
| Output Current | 27A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 6mA |
VND5E050MKTR-E Overview
As a result, it is packaged in the form of a Tape & Reel (TR).There is a 24-PowerBSOP (0.295, 7.50mm Width) package that includes it.A Surface Mount mounting is used for the LED driving board.General Purpose is the switch type that it owns.To ensure reliable performance, the temperature should be set to -40°C~150°C TJ.The lighting driver has a total of 2 outputs that are available for use.With a supply voltage of Not Required, the LED driving board operates.The maximum output voltage is N-Channel volts.Features of the lighting driver are Auto Restart.It is a member of the VND5E050 family.It has a total of 24 terminations.It is necessary to use the 24 pins in order to operate the LED driver.The LED driving board has a total of 1 functions.To comply with the operation criteria, the maximum output current is reduced to 27A.A supply voltage of 13V leads to high efficiency.Surface Mount is mounted in the way of this LED driving board.There are 24 pins in total on this board.There is 50mOhm resistance on the LED driver.There is an electrical component included in the VIPower? series.This results in a 27A output current.A self-contained LED driver with a capacity of Peripheral Drivers is contained in an econtainer.In order for the lighting driver to operate normally, the supply voltage (Vsup) should be maintained above 4.5V.It requires a maximum current requirement of 6mA.
VND5E050MKTR-E Features
Supplied from 13V
Resistance of 50mOhm
VND5E050MKTR-E Applications
There are a lot of STMicroelectronics VND5E050MKTR-E Power Switches ICs applications.
- Gaming
- Smartphone and PDA
- HDD, SSD
- Hot Swaps
- Storage (HDDs, SSDs)
- Hot Swap
- Low Voltage I/O System Power
- USB Ports/Hubs
- Hard Disk Drives
- Smart Phones, Feature Phones
