VND600PEP-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-PowerBSOP (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 30mOhm |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 96W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.8mm |
| Base Part Number | VND600 |
| Pin Count | 24 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 40A |
| Operating Supply Voltage | 36V |
| Interface | On/Off |
| Nominal Supply Current | 6mA |
| Output Configuration | High Side |
| Power Dissipation | 96W |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 6mA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 5.5V |
| Max Input Voltage | 36V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Rds On (Typ) | 30m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VND600PEP-E Overview
The LED driver's packaged as a Tube.There is a 24-PowerBSOP (0.295, 7.50mm Width) package that includes it.In this case, the LED driving board is mounted as Surface Mount.The switch type is General Purpose.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.There are 2 outputs available on this lighting driver.Operation is based on a supply voltage of Not Required.There is a maximum output voltage of N-Channel volts.It is part of the VND600 family of LED drivers.A total of 24 terminations have been found in it.In order to operate, 24 pins are used.There are 1 functions of the LED driver.The maximum output current is reduced to 40A to meet the operation criteria.The supply voltage can be 13V for high efficiency.It is mounted in the way of Surface Mount.It is equipped with a total of 24 pins.It has a resistance of 30mOhm.In this case, the output current is set to 25A.It is self-contained in an econtainer with a capacity of Peripheral Drivers.When using this LED driving board, it is recommended that the supply voltage is set to 36V.This LED driver can handle voltages up to 36V volts.It requires 5.5V volts as the minimum input voltage.It operates at a maximum current of 6mA.
VND600PEP-E Features
Supplied from 13V
Resistance of 30mOhm
VND600PEP-E Applications
There are a lot of STMicroelectronics VND600PEP-E Power Switches ICs applications.
- Hot Swap
- PDAs
- Gaming
- Wireless Modem Data Cards
- Mobile Communication Devices
- Hot-Swap Systems
- Smart Phones, Feature Phones
- Portable GPS
- Wireless/Networking Cards
- Portable Music Players
