VND600SP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
| Termination | Solder |
| ECCN Code | EAR99 |
| Resistance | 30mOhm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Voltage - Rated DC | 36V |
| Max Power Dissipation | 96.1W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Base Part Number | VND600 |
| Pin Count | 10 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 40A |
| Supply Voltage-Min (Vsup) | 5.5V |
| Interface | On/Off |
| Nominal Supply Current | 6mA |
| Output Configuration | High Side |
| Power Dissipation | 96.1W |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Input Current | 10mA |
| Load Current | 25A |
| Rds On (Typ) | 30m Ω (Max) |
| Drain to Source Resistance | 100mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Height Seated (Max) | 3.75mm |
| Length | 9.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VND600SP Overview
The package is in the form of a Tube.There is a PowerSO-10 Exposed Bottom Pad package that includes it.The mounting type of the LED driver is Surface Mount.There is a switch type of General Purpose.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.It is possible to use 2 outputs in the lighting driver.With a supply voltage of Not Required, the LED driving board operates.The maximum output voltage is N-Channel volts.It is a member of the VND600 family.It contains 10 terminations.The 10 pins are used to operate the LED driver.It is important to note that the LED driving board has 1 functions.This operation requires the maximum output current to be decreased to 40A.With a supply voltage of 13V, high efficiency is possible.Surface Mount is mounted in the way of this LED driving board.A total of 10 pins are included in this LED driver.30mOhm resistance is present in the lighting driver.When this case is used, the output current is set to 25A.In order to operate normally, the supply voltage (Vsup) must be maintained above 5.5V.
VND600SP Features
Supplied from 13V
Resistance of 30mOhm
VND600SP Applications
There are a lot of STMicroelectronics VND600SP Power Switches ICs applications.
- Telecom and Network Systems
- Portable Devices
- USB Ports/Hubs
- Set-Top Boxes
- HDD and SSD
- Wireless/Networking Cards
- Portable GPS
- USB3.1 Power Delivery
- Hot Swap
- Hot Swaps
