VND600SPTR-E
| Parameters | |
|---|---|
| ECCN Code | EAR99 |
| Resistance | 30mOhm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 96.1W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 13V |
| Base Part Number | VND600 |
| Pin Count | 10 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 25A |
| Interface | On/Off |
| Nominal Supply Current | 6mA |
| Output Configuration | High Side |
| Power Dissipation | 96.1W |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 6mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 30 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 5.5V |
| Max Input Voltage | 36V |
| Nominal Input Voltage | 13V |
| Turn-Off Delay Time | 30 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Rds On (Typ) | 30m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Height Seated (Max) | 3.75mm |
| Length | 9.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
VND600SPTR-E Overview
It is package in Tape & Reel (TR) case.There is a package for it in the PowerSO-10 Exposed Bottom Pad package.This LED driving board is mounted using the mounting type Surface Mount.It owns the General Purpose switch type.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.By default, it is set to output 2.To operate, it needs a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be obtained with this LED driver.The VND600 family contains this object.It has a total of 10 terminations.The 10 pins are used for the operation of the system.The LED driving board has a total of 2 functions.This operation requires the maximum output current to be decreased to 25A.As long as the supply voltage is 13V, high efficiency can be achieved.The lighting driver is mounted in the direction of Surface Mount.The LED driving board is equipped with a total of 10 pins.Currently, the LED driving board has 30mOhm resistance.In this case, the output current is set to 25A.Self-contained in an econtainer with a capacity of Peripheral Drivers, this LED driver is self-contained.The maximum input voltage is 36V volts.As a minimum input voltage, it requires 5.5V volts.This system has a maximum current requirement of 6mA.
VND600SPTR-E Features
Supplied from 13V
Resistance of 30mOhm
VND600SPTR-E Applications
There are a lot of STMicroelectronics VND600SPTR-E Power Switches ICs applications.
- Hard Disk Drives
- PC Card Hot Swap
- Telecom and Network Systems
- Hot Swaps
- Set-Top Boxes
- Wireless Modem Data Cards
- USB Power Distribution
- Set-top-box
- USB Protection
- HDD and SSD
