VND7020AJTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-PowerLFSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Cut Tape (CT) |
| Series | VIPower™ |
| Feature | Auto Restart, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | VND7020 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 45A |
| Supply Voltage-Min (Vsup) | 4V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 8mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 120 μs |
| Switch Type | General Purpose |
| Turn-Off Delay Time | 100 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4V~28V |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 22m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 1.7mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
VND7020AJTR Overview
The LED driver's packaged as a Cut Tape (CT).It is included in the package 16-PowerLFSOP (0.154, 3.90mm Width).This LED driving board is mounted using the mounting type Surface Mount.A General Purpose switch type is owned by it.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.There are 2 outputs available on this lighting driver.The LED driving board is powered by a voltage of Not Required.It has a maximum output voltage of N-Channel volts.In terms of features, the LED driving board has Auto Restart, Status Flag.As you can see, it comes from the VND7020 family.It contains 16 terminations.16 pins are used for operation.As far as functions are concerned, the lighting driver has 1.To meet the operation criteria, the maximum output current drops to 45A.A supply voltage of 13V leads to high efficiency.The lighting driver is mounted in the way of Surface Mount.A component of this type is included in the VIPower? series.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 4V.The maximum current required for its operation is 8mA.
VND7020AJTR Features
Supplied from 13V
VND7020AJTR Applications
There are a lot of STMicroelectronics VND7020AJTR Power Switches ICs applications.
- PC Cards
- Hard Disk Drives
- Portable/Handheld Devices
- Mobile Communication Devices
- Wearable Devices
- PDAs
- Handheld Devices
- Portable GPS Device
- Smart Phones, Feature Phones
- Portable Devices
