VND7NV04-1
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-251-3 Short Leads, IPak, TO-251AA |
| Number of Pins | 3 |
| Weight | 3.949996g |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | OMNIFET II™, VIPower™ |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Resistance | 60mOhm |
| Max Power Dissipation | 60W |
| Terminal Position | SINGLE |
| Number of Functions | 1 |
| Terminal Pitch | 2.25mm |
| Base Part Number | VND7N |
| Pin Count | 3 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 9A |
| Interface | On/Off |
| Nominal Supply Current | 100μA |
| Output Configuration | Low Side |
| Power Dissipation | 60W |
| Output Current | 6A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 100μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Drain to Source Voltage (Vdss) | 40V |
| Continuous Drain Current (ID) | 17A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 40V |
| Output Peak Current Limit-Nom | 9A |
| Rds On (Typ) | 60m Ω (Max) |
| Drain to Source Resistance | 60mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 7.4mm |
| Length | 6.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VND7NV04-1 Overview
Tube is the way it's packaged.This file is included in package TO-251-3 Short Leads, IPak, TO-251AA.This LED driving board is mounted using the mounting type Through Hole.It owns the General Purpose switch type.Keeping the temperature at -40°C~150°C TJ ensures reliable operation.The LED driver is equipped with 1 outputs.The LED driving board is powered by a voltage of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It comes under the family of VND7N.The termination count is 3.It is necessary to use the 3 pins in order to operate the LED driver.The LED driver has 1 functions.To comply with the operation criteria, the maximum output current is reduced to 9A.It is mounted in the way of Through Hole.3 pins are equipped with it.Lighting drivers with 60mOhm resistance are used.A component of this type is included in the OMNIFET II?, VIPower? series.This results in a 6A output current.For its operation, a maximum current requirement of 100μA is required.
VND7NV04-1 Features
Resistance of 60mOhm
VND7NV04-1 Applications
There are a lot of STMicroelectronics VND7NV04-1 Power Switches ICs applications.
- Low Voltage I/O System Power
- USB Ports/Hubs
- Various applications equipped with buttons
- Hot Swap
- Storage (HDDs, SSDs)
- PDAs
- Telecom and Network Systems
- Notebook and Tablet Computers
- Gaming
- Set-Top Boxes
