banner_page

VND7NV04

N-Channel 2.25mm PMIC OMNIFET II?, VIPower? Series VND7N 3 Pin TO-252-3, DPak (2 Leads + Tab), SC-63


  • Manufacturer: STMicroelectronics
  • Nocochips NO: 761-VND7NV04
  • Package: TO-252-3, DPak (2 Leads + Tab), SC-63
  • Datasheet: PDF
  • Stock: 257
  • Description: N-Channel 2.25mm PMIC OMNIFET II?, VIPower? Series VND7N 3 Pin TO-252-3, DPak (2 Leads + Tab), SC-63 (Kg)

Details

Tags

Parameters
Lifecycle Status ACTIVE (Last Updated: 8 months ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case TO-252-3, DPak (2 Leads + Tab), SC-63
Number of Pins 3
Weight 329.988449mg
Operating Temperature -40°C~150°C TJ
Packaging Tube
Series OMNIFET II™, VIPower™
Part Status Obsolete
Moisture Sensitivity Level (MSL) 3 (168 Hours)
Number of Terminations 2
ECCN Code EAR99
Resistance 60mOhm
Voltage - Rated DC 40V
Max Power Dissipation 60W
Terminal Position SINGLE
Terminal Form GULL WING
Number of Functions 1
Terminal Pitch 2.25mm
Current Rating 6A
Base Part Number VND7N
Pin Count 4
JESD-30 Code R-PSSO-G2
Number of Outputs 1
Output Type N-Channel
Max Output Current 6A
Interface On/Off
Nominal Supply Current 100μA
Output Configuration Low Side
Power Dissipation 60W
Output Current 6A
Voltage - Supply (Vcc/Vdd) Not Required
Max Supply Current 100μA
Input Type Non-Inverting
Switch Type General Purpose
Drain to Source Voltage (Vdss) 42V
Continuous Drain Current (ID) 13A
Ratio - Input:Output 1:1
Voltage - Load 36V Max
Fault Protection Current Limiting (Fixed), Over Temperature, Over Voltage
Drain to Source Breakdown Voltage 40V
Output Peak Current Limit-Nom 9A
Rds On (Typ) 60m Ω (Max)
Drain to Source Resistance 60mOhm
Built-in Protections TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL
Length 6.5mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

VND7NV04 Overview


The package is in the form of a Tube.The TO-252-3, DPak (2 Leads + Tab), SC-63 package includes it.The LED driver is mounted as Surface Mount.This switch is of type General Purpose.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.The lighting driver has a total of 1 outputs that are available for use.The LED driving board is powered by a voltage of Not Required.The maximum output voltage is N-Channel volts.It comes under the family of VND7N.The termination count is 2.It is necessary to use the 3 pins in order to operate the LED driver.Currently, the lighting driver has a total of 1 functions.Maximum output current falls to 6A when operation criteria are met.The LED driving board is mounted in the way of Surface Mount.This LED driver is equipped with a total of 4 pins.The LED driver has 60mOhm resistance.A component of this type is included in the OMNIFET II?, VIPower? series.As a result, the output current is set to 6A.For its operation, a maximum current requirement of 100μA is required.

VND7NV04 Features


Resistance of 60mOhm

VND7NV04 Applications


There are a lot of STMicroelectronics VND7NV04 Power Switches ICs applications.

  • Various applications equipped with buttons
  • Set-Top Boxes
  • USB Protection
  • Wireless Headsets
  • Hard Disk Drives
  • Hot Swap
  • Hot Swap
  • Wearable Devices
  • Solid State Drivers
  • Wireless/Networking Cards

Write a review

Note: HTML is not translated!
    Bad           Good