VND7NV04-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | OMNIFET II™, VIPower™ |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 60mOhm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 60W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 2.25mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VND7N |
| Pin Count | 3 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 9A |
| Interface | On/Off |
| Nominal Supply Current | 100μA |
| Output Configuration | Low Side |
| Power Dissipation | 60W |
| Output Current | 6A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 100μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Rise Time | 470ns |
| Drain to Source Voltage (Vdss) | 40V |
| Fall Time (Typ) | 350 ns |
| Turn-Off Delay Time | 500 ns |
| Continuous Drain Current (ID) | 6A |
| Threshold Voltage | 2.5V |
| Ratio - Input:Output | 1:1 |
| Gate to Source Voltage (Vgs) | 20V |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 40V |
| Output Peak Current Limit-Nom | 9A |
| Rds On (Typ) | 60m Ω (Max) |
| Drain to Source Resistance | 60mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Length | 6.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
VND7NV04-E Overview
Tube is the way it's packaged.It's included in the TO-252-3, DPak (2 Leads + Tab), SC-63 package.A Surface Mount mounting is used for the LED driving board.The switch type of this switch is General Purpose.Keeping the temperature at -40°C~150°C TJ ensures reliable operation.There are 1 outputs available on this lighting driver.To operate, it needs a supply voltage of Not Required.A maximum voltage of N-Channel volts is available from the output of this LED driver.It belongs to the VND7N family.It contains 2 terminations.The 3 pins are used for the operation of the system.Currently, the lighting driver has a total of 1 functions.The maximum output current must drop to 9A to meet the operation criteria.The lighting driver is mounted in the way of Surface Mount.The LED driver has a total of 3 pins.Lighting drivers with 60mOhm resistance are used.There is an electrical component included in the OMNIFET II?, VIPower? series.In this case, the output current will be set to 6A.It requires a maximum current requirement of 100μA.
VND7NV04-E Features
Resistance of 60mOhm
VND7NV04-E Applications
There are a lot of STMicroelectronics VND7NV04-E Power Switches ICs applications.
- USB Power Distribution
- Notebook and Tablet Computers
- Portable GPS
- Portable Devices
- USB3.1 Power Delivery
- Handheld Devices
- Wireless/Networking Cards
- Low Voltage I/O System Power
- Set-Top Boxes
- Telecom and Network Systems
