VND830ASP13TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | VIPower™ |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
| Termination | Gull Wing |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 74W |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Base Part Number | VND830 |
| Pin Count | 10 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 6A |
| Supply Voltage-Max (Vsup) | 36V |
| Power Supplies | 13V |
| Supply Voltage-Min (Vsup) | 5.5V |
| Interface | On/Off |
| Nominal Supply Current | 7mA |
| Output Configuration | High Side |
| Power Dissipation | 74W |
| Output Current | 6A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Input Current | 10mA |
| Load Current | 25A |
| Output Peak Current Limit-Nom | 9A |
| Rds On (Typ) | 60m Ω (Max) |
| Drain to Source Resistance | 120mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Height Seated (Max) | 3.65mm |
| Length | 9.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
VND830ASP13TR Overview
A Tape & Reel (TR) is used to package it.It is included with the PowerSO-10 Exposed Bottom Pad package as well.Surface Mount is the mounting type of the LED driver.The switch type of this switch is General Purpose.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.There is a default setting of 2 for output.The LED driving board is powered by a voltage of Not Required.A maximum output voltage of N-Channel volts can be obtained with this LED driver.It is part of the VND830 family of LED drivers.It has a total of 10 terminations.It is necessary to use the 10 pins in order to operate the LED driver.It is important to note that the LED driving board has 1 functions.The maximum output current must drop to 6A to meet the operation criteria.Supply voltages of 13V allow for high efficiency.In this case, it is mounted in the way of Surface Mount.10 pins are connected to it in total.It is part of the VIPower? series.The output current is set to 6A in this case.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.In this case, Vsup (maximum supply voltage) is set to 36V.Normal operation requires Vsup above 5.5V.13V is the power supply of the part.
VND830ASP13TR Features
Supplied from 13V
VND830ASP13TR Applications
There are a lot of STMicroelectronics VND830ASP13TR Power Switches ICs applications.
- Portable Video Game Players
- Set-Top Boxes
- Telecom and Network Systems
- Smartphone and PDA
- Wireless Modem Data Cards
- PDAs
- Hot Swap
- Low Voltage I/O System Power
- Storage (HDDs, SSDs)
- USB Protection
