VND830LSP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 12 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | VIPower™ |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 60mOhm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 74W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Base Part Number | VND830 |
| Pin Count | 10 |
| JESD-30 Code | R-PDSO-G10 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 23A |
| Operating Supply Voltage | 36V |
| Power Supplies | 13V |
| Interface | On/Off |
| Current - Output (Max) | 18A |
| Nominal Supply Current | 12μA |
| Output Configuration | High Side |
| Power Dissipation | 74W |
| Output Current | 23A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 12μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 5.5V |
| Max Input Voltage | 36V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 23A |
| Rds On (Typ) | 60m Ω (Max) |
| Built-in Protections | OVER CURRENT; OVER VOLTAGE; UNDER VOLTAGE |
| Height Seated (Max) | 3.75mm |
| Length | 9.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
VND830LSP Overview
As you can see, it's packaged in the way of a Tube.This file is included in package PowerSO-10 Exposed Bottom Pad.Surface Mount is the mounting type of the LED driver.There is a switch type of General Purpose.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.There is a default setting of 2 for output.The LED driving board is powered by a voltage of Not Required.There is a maximum output voltage of N-Channel volts.As far as features are concerned, the LED driving board has Auto Restart.It comes under the family of VND830.There are 10 terminations in it.During operation, the 12 pins are used.It contains 1 functions.From the lighting driver, there is a maximum output of 18AV.The maximum output current must drop to 23A to meet the operation criteria.Supply voltages of 13V allow for high efficiency.Surface Mount is mounted in the way of this lighting driver.10 pins are equipped with it.There is 60mOhm resistance on the LED driver.These electrical components are part of the VIPower? series.As a result, the output current is set to 23A.A self-contained econtainer holding Peripheral Drivers capacity contains this lighting driver.This part's power supply is 13V.For maximum efficiency, the supply voltage should be set to 36V.It has a maximum input voltage of 36V volts.It requires 5.5V volts as the minimum input voltage.A maximum current requirement of 12μA is required for its operation.
VND830LSP Features
Supplied from 13V
Resistance of 60mOhm
VND830LSP Applications
There are a lot of STMicroelectronics VND830LSP Power Switches ICs applications.
- PC Card Hot Swap
- USB Power Distribution
- Storage Drives
- USB3.1 Power Delivery
- Hot Swaps
- Notebook PC
- PC Cards
- Wireless/Networking Cards
- Handheld Devices
- Hot Swap
