VNL5050S5TR-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | OMNIFET III™, VIPower™ |
| JESD-609 Code | e3 |
| Feature | Auto Restart, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 50mOhm |
| Terminal Finish | Tin (Sn) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | VNL5050 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 27A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 3.5V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Operating Supply Current | 30μA |
| Nominal Supply Current | 25μA |
| Output Configuration | Low Side |
| Output Current | 19A |
| Voltage - Supply (Vcc/Vdd) | 3.5V~5.5V |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Output Current per Channel | 19A |
| Rise Time | 10μs |
| Fall Time (Typ) | 10 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Rds On (Typ) | 50m Ω (Max) |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VNL5050S5TR-E Overview
As you can see, it's packaged in the way of a Tape & Reel (TR).This package is included in 8-SOIC (0.154, 3.90mm Width).The mounting type of the LED driver is Surface Mount.General Purpose is the switch type it owns.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.The LED driver has a total of 1 outputs.The LED driving board operates at 3.5V~5.5V volts.Voltage output is N-Channel volts at maximum.Features of the lighting driver are Auto Restart, Status Flag.There is a VNL5050 family of things that it belongs to.The termination count is 8.The operation is carried out using the 8 pins.Currently, the lighting driver has a total of 1 functions.To comply with the operation criteria, the maximum output current is reduced to 27A.It is possible to achieve a high level of efficiency with a supply voltage of 5V.This lighting driver is mounted in the way of Surface Mount.A total of 8 pins are present on it.50mOhm resistance is present in the lighting driver.It belongs to the OMNIFET III?, VIPower? series.In this case, the output current is set to 19A.A maximum supply voltage of 5.5V is set in Vsup.In order to operate normally, the supply voltage (Vsup) must remain above 3.5V.This LED driving board uses an analog IC POWER SUPPLY SUPPORT CIRCUIT.In total, there are 1 channels available.
VNL5050S5TR-E Features
Supplied from 5V
Resistance of 50mOhm
1 channels
VNL5050S5TR-E Applications
There are a lot of STMicroelectronics VNL5050S5TR-E Power Switches ICs applications.
- Hard Disk Drives
- Portable GPS
- Hot-Swap Systems
- Wireless/Networking Cards
- USB Power Distribution
- Solid State Drivers
- Storage (HDDs, SSDs)
- PC Card Hot Swap
- Hot Swap
- Smart Phones, Feature Phones
