VNLD5300TR-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Cut Tape (CT) |
| Series | OMNIFET III™, VIPower™ |
| Feature | Auto Restart, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | VNLD5300 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 2A |
| Supply Voltage-Min (Vsup) | 4.5V |
| Interface | On/Off |
| Output Configuration | Low Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 65μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Fall Time (Typ) | 3 μs |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 300m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VNLD5300TR-E Overview
Cut Tape (CT) is how it's packaged.There is a 8-SOIC (0.154, 3.90mm Width) package that includes it.Surface Mount is the mounting type of the LED driver.General Purpose is the switch type that it owns.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.The lighting driver has a total of 2 outputs that are available for use.It uses a supply voltage of Not Required to operate.There is a maximum output voltage of N-Channel volts.As far as features are concerned, the LED driving board has Auto Restart, Status Flag.It is part of the VNLD5300 family of LED drivers.It has a total of 8 terminations.The operation is carried out using the 8 pins.Currently, the lighting driver has a total of 1 functions.This results in the maximum output current dropping to 2A to meet the operation criteria.Supply voltages of 5V allow for high efficiency.The LED driving board is mounted in the way of Surface Mount.This electrical component is included in the OMNIFET III?, VIPower? series.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 4.5V.65μA is the maximum current required to operate it.
VNLD5300TR-E Features
Supplied from 5V
VNLD5300TR-E Applications
There are a lot of STMicroelectronics VNLD5300TR-E Power Switches ICs applications.
- Solid-State Drives
- Hot Swap
- Set-Top Boxes
- Portable GPS
- PC Cards
- USB Power Distribution
- Handheld Devices
- Portable GPS Device
- Various applications equipped with buttons
- Wireless Modem Data Cards
