VNP10N07
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 8 months ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-220-3 |
| Number of Pins | 3 |
| Weight | 2.240009g |
| Packaging | Tube |
| Series | OMNIFET™, VIPower™ |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Resistance | 100mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Voltage - Rated DC | 70V |
| Max Power Dissipation | 50W |
| Technology | MOS |
| Terminal Position | SINGLE |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Reach Compliance Code | not_compliant |
| Current Rating | 10A |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | VNP10N |
| Pin Count | 3 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 7A |
| Operating Supply Voltage | 18V |
| Voltage | 70V |
| Interface | On/Off |
| Nominal Supply Current | 250μA |
| Current | 10A |
| Output Configuration | Low Side |
| Power Dissipation | 31W |
| Output Current | 7A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 250μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Output Characteristics | OPEN-DRAIN |
| Drain to Source Voltage (Vdss) | 70V |
| Continuous Drain Current (ID) | 10A |
| Output Polarity | TRUE |
| Ratio - Input:Output | 1:1 |
| Input Characteristics | SCHMITT TRIGGER |
| Voltage - Load | 55V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 70V |
| Turn On Time | 0.9 μs |
| Load Current | 10A |
| Output Peak Current Limit-Nom | 10A |
| Rds On (Typ) | 100m Ω (Max) |
| Drain to Source Resistance | 100mOhm |
| Turn Off Time | 6 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height | 15.75mm |
| Length | 10.4mm |
| Width | 4.6mm |
| RoHS Status | ROHS3 Compliant |
VNP10N07 Overview
The package is in the form of a Tube.It is included in the package TO-220-3.It has been mounted as Through Hole on the LED driver.General Purpose is the switch type it owns.In this LED driver, there are no outputs available.The LED driving board is powered by a voltage of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It is part of the VNP10N family of LED drivers.In total, there are 3 terminations.For operation, we use the 3 pins.As far as the lighting driver is concerned, there are 1 functions.This results in the maximum output current dropping to 7A to meet the operation criteria.Through Hole is mounted in the way of this lighting driver.The LED driver has a total of 3 pins.There is 100mOhm resistance on the LED driver.It is part of the OMNIFET?, VIPower? series.This case has the output current set to 7A.In order to maximize efficiency, the supply voltage should be set at 18V.A maximum current requirement of 250μA is required for its operation.
VNP10N07 Features
Resistance of 100mOhm
VNP10N07 Applications
There are a lot of STMicroelectronics VNP10N07 Power Switches ICs applications.
- Notebook and Tablet Computers
- Storage (HDDs, SSDs)
- Smart Phones, Feature Phones
- USB Power Distribution
- Handheld Devices
- Solid-State Drives
- Various applications equipped with buttons
- HDD and SSD
- Portable GPS
- Hot Swap
