VNQ5E050AKTR-E
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.8mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | VNQ5E050 |
| Pin Count | 24 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 27A |
| Operating Supply Voltage | 13V |
| Supply Voltage-Max (Vsup) | 28V |
| Power Supplies | 8/28V |
| Interface | On/Off |
| Nominal Supply Current | 14mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 14mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 20 μs |
| Switch Type | General Purpose |
| Output Current per Channel | 19A |
| Turn-Off Delay Time | 35 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.5V~28V |
| Driver Number of Bits | 4 |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
| Rds On (Typ) | 50m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 10.3mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOP (0.295, 7.50mm Width) Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | VIPower™ |
| Feature | Auto Restart |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 50mOhm |
| Subcategory | Peripheral Drivers |
VNQ5E050AKTR-E Overview
Tape & Reel (TR) is the way it's packaged.Package 24-SOP (0.295, 7.50mm Width) Exposed Pad contains it.Surface Mount is the mounting type of the LED driver.General Purpose is the type of switch owned by it.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.The LED driver is equipped with 4 outputs.To operate, it needs a supply voltage of Not Required.Voltage output is N-Channel volts at maximum.It is equipped with Auto Restart features.The VNQ5E050 family consists of this type.It consists of 24 terminations in total.24 pins are used for operation.As far as the lighting driver is concerned, there are 1 functions.In order to meet the operation criteria, the maximum output current drops to 27A.High efficiency is possible at 13V supply voltage.In this case, it is mounted in the way of Surface Mount.24 pins are equipped with it.It has 50mOhm resistance.This electrical component is part of the VIPower? series.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.The LED driver is configured with a maximum supply voltage of 28V (Vsup).This part has a power supply of 8/28V.The supply voltage should be set at 13V for best efficiency.The maximum current required for its operation is 14mA.
VNQ5E050AKTR-E Features
Supplied from 13V
Resistance of 50mOhm
VNQ5E050AKTR-E Applications
There are a lot of STMicroelectronics VNQ5E050AKTR-E Power Switches ICs applications.
- Hot Swaps
- Storage Drives
- Portable GPS Device
- Low Voltage I/O System Power
- Portable/Handheld Devices
- Storage (HDDs, SSDs)
- Hot Swap
- HDD, SSD
- Hot-Swap Systems
- Portable GPS
