VNQ600AP-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | NRND (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 35mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 6.25W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 4 |
| Supply Voltage | 13V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VNQ600 |
| Pin Count | 28 |
| Number of Outputs | 4 |
| Output Type | N-Channel |
| Max Output Current | 40A |
| Operating Supply Voltage | 36V |
| Interface | On/Off |
| Nominal Supply Current | 6mA |
| Output Configuration | High Side |
| Power Dissipation | 6.25W |
| Output Current | 15A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 6mA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 5.5V |
| Max Input Voltage | 36V |
| Output Current per Channel | 15A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Driver Number of Bits | 4 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 35m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Height Seated (Max) | 2.65mm |
| Length | 17.9mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VNQ600AP-E Overview
A Tube is used to package it.In the 28-SOIC (0.295, 7.50mm Width) package, it is included.The mounting type of the LED driver is Surface Mount.General Purpose is the switch type that it owns.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.There are 4 outputs available on this lighting driver.Operation is based on Not Required supply voltage.A maximum voltage of N-Channel volts is available from the output of this LED driver.It comes under the family of VNQ600.A total of 28 terminations have been recorded.For operation, we use the 28 pins.The LED driver has 4 functions.This results in the maximum output current dropping to 40A to meet the operation criteria.Supply voltages of 13V allow for high efficiency.In this case, it is mounted in the way of Surface Mount.It is equipped with a total of 28 pins.Lighting drivers with 35mOhm resistance are used.In this case, the output current is set to 15A.The LED driver is self-contained in an econtainer with Peripheral Drivers capacity.For maximum efficiency, the supply voltage should be set to 36V.This LED driver can handle voltages up to 36V volts.The input voltage minimum is 5.5V volts.It requires a maximum current requirement of 6mA.
VNQ600AP-E Features
Supplied from 13V
Resistance of 35mOhm
VNQ600AP-E Applications
There are a lot of STMicroelectronics VNQ600AP-E Power Switches ICs applications.
- Portable GPS Device
- HDD and SSD
- Hot-Swap Systems
- Hot Swaps
- Set-Top Boxes
- Notebook and Tablet Computers
- Telecom and Network Systems
- USB Protection
- Portable Music Players
- Gaming
