Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 6 months ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-PowerSOIC (0.370, 9.40mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Series |
VIPower™ |
JESD-609 Code |
e3 |
Feature |
Status Flag |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
90mOhm |
Terminal Finish |
Matte Tin (Sn) - annealed |
Subcategory |
Peripheral Drivers |
Max Power Dissipation |
78W |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
250 |
Number of Functions |
4 |
Supply Voltage |
13V |
Terminal Pitch |
1.27mm |
Base Part Number |
VNQ660 |
Pin Count |
10 |
Number of Outputs |
4 |
Output Type |
N-Channel |
Max Output Current |
10A |
Operating Supply Voltage |
36V |
Power Supplies |
13V |
Interface |
On/Off |
Nominal Supply Current |
6mA |
Output Configuration |
High Side |
Power Dissipation |
78W |
Output Current |
10A |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Max Supply Current |
6mA |
Input Type |
Non-Inverting |
Switch Type |
General Purpose |
Min Input Voltage |
5.5V |
Max Input Voltage |
36V |
Ratio - Input:Output |
1:1 |
Voltage - Load |
6V~36V |
Driver Number of Bits |
4 |
Fault Protection |
Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
Rds On (Typ) |
90m Ω (Max) |
Built-in Protections |
TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
Height Seated (Max) |
3.75mm |
Width |
7.5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
VNQ690SPTR-E Overview
As you can see, it's packaged in the way of a Tape & Reel (TR).It is included in the package 10-PowerSOIC (0.370, 9.40mm Width).In this case, the LED driving board is mounted as Surface Mount.There is a switch type of General Purpose.It is best to set the temperature to -40°C~150°C TJ to ensure reliable operation.By default, it is set to output 4.The LED driving board is powered by a voltage of Not Required.It has a maximum output voltage of N-Channel volts.It has a total of Status Flag features.This object belongs to the VNQ660 family.The termination count is 10.10 pins are used for operation.It contains 4 functions.It is necessary to reduce the maximum output current to 10A to meet the operation criteria.High efficiency is possible when the supply voltage is set to 13V.The lighting driver is mounted in the way of Surface Mount.In total, it has 10 pins.90mOhm is the resistance of the lighting driver.This electrical component can be found in the VIPower? series.This case results in a 10A output current.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.In this case, the power supply is 13V.The supply voltage should be set at 36V for best efficiency.A maximum input voltage of 36V volts can be applied to it.The minimum input voltage is 5.5V volts.6mA is the maximum current required to operate it.
VNQ690SPTR-E Features
Supplied from 13V
Resistance of 90mOhm
VNQ690SPTR-E Applications
There are a lot of STMicroelectronics VNQ690SPTR-E Power Switches ICs applications.
- Hard Disk Drives
- USB3.1 Power Delivery
- PC Card Hot Swap
- Hot-Swap Systems
- Portable GPS Device
- USB Power Distribution
- Telecom and Network Systems
- USB Protection
- Handheld Devices
- Smart Phones, Feature Phones