VNQ860SP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | VIPower™ |
| JESD-609 Code | e3 |
| Feature | Auto Restart, Status Flag |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 90W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 24V |
| Terminal Pitch | 1.27mm |
| Base Part Number | VNQ860 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Output Type | N-Channel |
| Max Output Current | 250mA |
| Operating Supply Voltage | 41V |
| Supply Voltage-Max (Vsup) | 36V |
| Power Supplies | 8/36V |
| Interface | On/Off |
| Nominal Supply Current | 120mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Driver Number of Bits | 4 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 0.7A |
| Rds On (Typ) | 270m Ω (Max) |
| Drain to Source Resistance | 540mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 3.75mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VNQ860SP Overview
A Tube is used to package it.It's included in the PowerSO-10 Exposed Bottom Pad package.The mounting type of the LED driver is Surface Mount.General Purpose is the switch type that it owns.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.By default, it is set to output 4.The LED driving board operates at Not Required volts.There is a maximum output voltage of N-Channel volts.As far as features are concerned, the LED driving board has Auto Restart, Status Flag.It is part of the VNQ860 family of LED drivers.A total of 10 terminations have been found in it.The operation is carried out using the 10 pins.The LED driver has 1 functions.In order to meet the operation criteria, the maximum output current drops to 250mA.High efficiency is possible when the supply voltage is set to 24V.Surface Mount is mounted in the way.The LED driver has a total of 10 pins.These electrical components are part of the VIPower? series.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.The Vsup value (maximum supply voltage) is set to 36V.The power supply of the part is 8/36V.It is recommended to set the supply voltage to 41V for optimum efficiency.
VNQ860SP Features
Supplied from 24V
VNQ860SP Applications
There are a lot of STMicroelectronics VNQ860SP Power Switches ICs applications.
- Wireless Modem Data Cards
- Portable GPS Device
- Hot Swap
- Low Voltage I/O System Power
- Hard Disk Drives
- Wireless/Networking Cards
- USB Protection
- USB Ports/Hubs
- Notebook PC
- HDD, SSD
