VNV28N04
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | OMNIFET™, VIPower™ |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 35mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 83W |
| Technology | MOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Base Part Number | VNV28 |
| Pin Count | 10 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 19A |
| Operating Supply Voltage | 18V |
| Interface | On/Off |
| Nominal Supply Current | 250μA |
| Output Configuration | Low Side |
| Power Dissipation | 83W |
| Output Current | 19A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 250μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Output Characteristics | OPEN-DRAIN |
| Continuous Drain Current (ID) | 28A |
| Output Polarity | TRUE |
| Ratio - Input:Output | 1:1 |
| Input Characteristics | SCHMITT TRIGGER |
| Voltage - Load | 31V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 42V |
| Turn On Time | 0.7 μs |
| Output Peak Current Limit-Nom | 28A |
| Rds On (Typ) | 35m Ω (Max) |
| Drain to Source Resistance | 35mOhm |
| Built-in Protections | OVER CURRENT; THERMAL; ZENER CLAMP |
| Height Seated (Max) | 3.75mm |
| Length | 9.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VNV28N04 Overview
As you can see, it's packaged in the way of a Tube.In the PowerSO-10 Exposed Bottom Pad package, it is included.This lighting drivere has a mounting type of Surface Mount.General Purpose is the type of switch owned by it.It is best to set the temperature to -40°C~150°C TJ to ensure reliable operation.There is a default setting of 1 for output.To operate, it needs a supply voltage of Not Required.There is a maximum output voltage of N-Channel volts on this LED driver.It is part of the VNV28 family of LED drivers.A total of 10 terminations have been found in it.For operation, we use the 10 pins.There are 1 functions of the LED driver.To comply with the operation criteria, the maximum output current is reduced to 19A.Surface Mount is mounted in the way of this lighting driver.10 pins are equipped with it.Lighting drivers with 35mOhm resistance are used.It is included in the OMNIFET?, VIPower? series.In this case, the output current will be set to 19A.For maximum efficiency, the supply voltage should be set to 18V.It has a maximum current requirement of 250μA.
VNV28N04 Features
Resistance of 35mOhm
VNV28N04 Applications
There are a lot of STMicroelectronics VNV28N04 Power Switches ICs applications.
- Various applications equipped with buttons
- Hard Disk Drives
- Gaming
- PC Card Hot Swap
- Telecom and Network Systems
- Solid State Drivers
- Mobile Communication Devices
- Wireless Headsets
- Notebook and Tablet Computers
- HDD, SSD
