banner_page

VNV35NV04

N-Channel PMIC OMNIFET II?, VIPower? Series VNV35 10 Pin PowerSO-10 Exposed Bottom Pad


  • Manufacturer: STMicroelectronics
  • Nocochips NO: 761-VNV35NV04
  • Package: PowerSO-10 Exposed Bottom Pad
  • Datasheet: PDF
  • Stock: 834
  • Description: N-Channel PMIC OMNIFET II?, VIPower? Series VNV35 10 Pin PowerSO-10 Exposed Bottom Pad (Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case PowerSO-10 Exposed Bottom Pad
Number of Pins 10
Operating Temperature -40°C~150°C TJ
Packaging Tube
Series OMNIFET II™, VIPower™
JESD-609 Code e3
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 3 (168 Hours)
Number of Terminations 10
ECCN Code EAR99
Resistance 10mOhm
Terminal Finish Matte Tin (Sn) - annealed
Max Power Dissipation 125W
Terminal Position DUAL
Terminal Form GULL WING
Number of Functions 1
Base Part Number VNV35
Pin Count 10
Number of Outputs 1
Output Type N-Channel
Max Output Current 30A
Operating Supply Voltage 18V
Interface On/Off
Nominal Supply Current 100μA
Output Configuration Low Side
Power Dissipation 125W
Output Current 30A
Voltage - Supply (Vcc/Vdd) Not Required
Max Supply Current 100μA
Input Type Non-Inverting
Turn On Delay Time 12 μs
Switch Type General Purpose
Drain to Source Voltage (Vdss) 40V
Turn-Off Delay Time 120 μs
Continuous Drain Current (ID) 30A
Ratio - Input:Output 1:1
Voltage - Load 36V Max
Fault Protection Current Limiting (Fixed), Over Temperature, Over Voltage
Drain to Source Breakdown Voltage 40V
Output Peak Current Limit-Nom 45A
Rds On (Typ) 10m Ω (Max)
Drain to Source Resistance 10Ohm
Built-in Protections TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL
Height Seated (Max) 3.75mm
Length 9.4mm
Width 7.5mm
Radiation Hardening No
RoHS Status ROHS3 Compliant

VNV35NV04 Overview


It is packaged in the manner of a Tube.In the PowerSO-10 Exposed Bottom Pad package, it is included.The lighting driver is mounted in the Surface Mount position.General Purpose is the switch type it owns.To ensure reliable performance, the temperature should be set to -40°C~150°C TJ.The LED driver has 1 outputs.In order to operate, it requires a voltage supply of Not Required.A maximum output voltage of N-Channel volts has been specified.The VNV35 family consists of this type.In total, there are 10 terminations.The 10 pins are used for the operation of the system.The LED driving board has a total of 1 functions.The maximum output current must drop to 30A to meet the operation criteria.The lighting driver is mounted in the direction of Surface Mount.The LED driver has a total of 10 pins.There is 10mOhm resistance on the LED driver.This electrical component is included in the OMNIFET II?, VIPower? series.In this case, the output current is set to 30A.A supply voltage of 18V is recommended for maximum efficiency.It requires a maximum current requirement of 100μA.

VNV35NV04 Features


Resistance of 10mOhm

VNV35NV04 Applications


There are a lot of STMicroelectronics VNV35NV04 Power Switches ICs applications.

  • Low Voltage I/O System Power
  • USB Protection
  • Set-Top Boxes
  • Portable GPS
  • Storage (HDDs, SSDs)
  • Set-top-box
  • Wearable Devices
  • USB Ports/Hubs
  • Hot-Swap Systems
  • USB3.1 Power Delivery

Write a review

Note: HTML is not translated!
    Bad           Good