XCF16PVOG48C
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.724, 18.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 48 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tray |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.32.00.51 |
| Technology | CMOS |
| Voltage - Supply | 1.65V~2V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Frequency | 50MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | XCF*P |
| Pin Count | 48 |
| Operating Supply Voltage | 1.8V |
| Supply Voltage-Max (Vsup) | 2V |
| Supply Voltage-Min (Vsup) | 1.65V |
| Programmable Type | In System Programmable |
| Interface | Parallel |
| Memory Size | 16Mb |
| Memory Type | FLASH |
| Supply Current-Max | 0.04mA |
| Organization | 16MX1 |
| Memory Width | 1 |
| Memory Density | 16777216 bit |
| Parallel/Serial | SERIAL |
| Endurance | 20000 Write/Erase Cycles |
| Data Retention Time-Min | 20 |
| Max Junction Temperature (Tj) | 125°C |
| Ambient Temperature Range High | 85°C |
| Height | 1.2mm |
| Length | 18.45mm |
| Width | 12mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
XCF16PVOG48C Overview
This package makes use of the 48-TFSOP (0.724, 18.40mm Width) programming language.External packaging of type Tray.A qualified individual to operate within -40°C~85°C is required.In System Programmable allows for programmability.An electric current of 1.65V~2V is applied to it.This memory device is mounted in Surface Mount.Currently, data storage can only store data up to 16Mb bytes.Other components related to "XCF*P" can also be found by searching the word.The supply voltage of the device must be 1.8V in order to operate correctly.48 terminations with different functions.FPGA is possible to use this memory device at a maximum voltage of 2V.FPGA is imperative that the voltage of the device supply is at least 1.65V if the device is to work properly.Reflow soldering should be done at no higher than 260 degrees.48 pins are located on the board.In this memory, data is transmitted using the SERIAL process.A memory chip can operate at a voltage no greater than 0.04mA.The part comes with a set of 48 pins.Before using the part in a circuit, it is recommended that the user apply 1.8V before the part is used in order to ensure that it runs safely and reliably in the circuit.Memory is also referred to as a FLASH memory.A swicthing controller operates at a frequency of 50MHz.
XCF16PVOG48C Features
Operating temperature: -40°C~85°C.
In System Programmable program capability.
SERIAL processing.
FLASH memory
Frequency: 50MHz.
XCF16PVOG48C Applications
There are a lot of Xilinx Inc. XCF16PVOG48C applications of configuration proms for FPGAs.
- embedded logic
- supercomputers
- eDRAM
- graphics card
- cell phones
- mainframes
- main computer memory
- hard disk drive (HDD)
- Camcorders
- networks
